View All Items

Title: A direct thrust measurement system for a waterjet propelled, free running USV.
Creator: Grimes, John A., von Ellenrieder, Karl, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: The relationship between cross-flow at a waterjet inlet and delivered thrust is not fully understood. A direct thrust measurement system was designed for a waterjet propelled, free running USV. To induce sway velocity at the waterjet inlet, which was considered equivalent to the cross flow, circles of varying radii were performed at Reynolds Numbers between 3.48 x 106 and 8.7 x 106 and radii from 2.7 to 6.3 boat lengths. Sway velocities were less than twenty percent of mean forward speed with...
Show moreThe relationship between cross-flow at a waterjet inlet and delivered thrust is not fully understood. A direct thrust measurement system was designed for a waterjet propelled, free running USV. To induce sway velocity at the waterjet inlet, which was considered equivalent to the cross flow, circles of varying radii were performed at Reynolds Numbers between 3.48 x 106 and 8.7 x 106 and radii from 2.7 to 6.3 boat lengths. Sway velocities were less than twenty percent of mean forward speed with slip angles that were less than 20°. Thrust Loading Coefficients were compared to sway as a percent of forward speed. In small radius turns, no relationship was seen, while in larger radius turns, peaks of sway velocity corresponded with drops in thrust, but this was determined to be caused by reduced vehicle yaw in these intervals . Decoupling of thrust and yaw rate is recommended for future research.
Show less
Date Issued: 2013
PURL: http://purl.flvc.org/fau/fd/FA0004023
Subject Headings: Oceanographic instruments -- Evaluation, Propellers, Ship propulsion, Ships -- Hydrodynamics, Stability of ships
Format: Document (PDF)

Title: Accelerated curing of concrete with high volume pozzolans - resistivity, diffusivity and compressive strength.
Creator: Liu, Yanbo., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: This investigation presents results of the temperature effect on durability properties (resistivity and diffusivity) and compressive strength of concrete with pozzolans, and the effect of pozzolanic admixtures on microstructure and chemical compositions of concrete pore solution. ... Temperature dependence of electrical resistivity and chloride diffusivity was studied by dynamic temperature tests. Accelerated curing regimes involving curing concrete specimens in 35À C lime water with...
Show moreThis investigation presents results of the temperature effect on durability properties (resistivity and diffusivity) and compressive strength of concrete with pozzolans, and the effect of pozzolanic admixtures on microstructure and chemical compositions of concrete pore solution. ... Temperature dependence of electrical resistivity and chloride diffusivity was studied by dynamic temperature tests. Accelerated curing regimes involving curing concrete specimens in 35À C lime water with different durations were tested. Compressive strength test, resisivity measurement and rapid chloride migration (RCM) tests were performed. A leaching method was used to measure pH and conductivity of concrete pore solution. ... The accelerated curing regimes were found to increase the compressive strength and resistance to chloride ion penetration at short-term and long-term. With the developed correlation between resistivity and migration coefficients, it is possible to employ the resistivity measurement as an alternative or replacement of the RCM test to evaluate resistance of chloride ion penetration of concrete. Pozzolanic admixtures were found to decrease both pH and conductivity of concrete pore solution as the replacement ratio increased. Moreover, the migration coefficients were found to be greatly correlated to the microstructure properties of concrete, such as porosity, formation factor and tortuosity.
Show less
Date Issued: 2012
PURL: http://purl.flvc.org/FAU/3358603
Subject Headings: Pavements, Concrete, Additives, Quality control, Waste products as road materials, Reinforced concrete, Corrosion, Testing
Format: Document (PDF)

Title: The acoustic far field of a turbulent boundary layer flow calculated from RANS simulations of the flow.
Creator: Blanc, Jean-Baptiste., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Boundary layers are regions where turbulence develops easily. In the case where the flow occurs on a surface showing a certain degree of roughness, turbulence eddies will interact with the roughness elements and will produce an acoustic field. This thesis aims at predicting this type of noise with the help of the Computational Fluid Dynamics (CFD) simulation of a wall jet using the Reynolds Average Navier-Stokes (RANS) equations. A frequency spectrum is reconstructed using a representation of...
Show moreBoundary layers are regions where turbulence develops easily. In the case where the flow occurs on a surface showing a certain degree of roughness, turbulence eddies will interact with the roughness elements and will produce an acoustic field. This thesis aims at predicting this type of noise with the help of the Computational Fluid Dynamics (CFD) simulation of a wall jet using the Reynolds Average Navier-Stokes (RANS) equations. A frequency spectrum is reconstructed using a representation of the turbulence with uncorrelated sheets of vorticity. Both aerodynamic and acoustic results are compared to experimental measurements of the flow. The CFD simulation of the flow returns consistent results but would benefit from a refinement of the grid. The surface pressure spectrum presents a slope in the high frequencies close to the experimental spectrum. The far field noise spectrum has a 5dB difference to the experiments.
Show less
Date Issued: 2009
PURL: http://purl.flvc.org/FAU/368611
Subject Headings: Computational fluid dynamics, Turbulence, Mathematical models, Fluid mechanics, Mathematical models, Acoustical engineering
Format: Document (PDF)

Title: Acoustic tracking of an unmanned underwater vehicle using a passive ultrashort baseline array and a single long baseline beacon.
Creator: Seaton, Kyle L., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: This thesis discusses a new approach to tracking the REMUS 100 AUV using a modified version of the Florida Atlantic University (FAU) ultrashort baseline (USBL) acoustic positioning system (APS). The REMUS 100 is designed to utilize a long baseline (LBL) acoustic positioning system to obtain positioning data in mid-mission. If the placement of one of the transponders of the LBL field is known, then tracking the position of the REMUS 100 AUV using a passive USBL array is possible. As part of...
Show moreThis thesis discusses a new approach to tracking the REMUS 100 AUV using a modified version of the Florida Atlantic University (FAU) ultrashort baseline (USBL) acoustic positioning system (APS). The REMUS 100 is designed to utilize a long baseline (LBL) acoustic positioning system to obtain positioning data in mid-mission. If the placement of one of the transponders of the LBL field is known, then tracking the position of the REMUS 100 AUV using a passive USBL array is possible. As part of the research for this thesis, the FAU USBL system was used to find a relative range between the REMUS 100 ranger and a LBL transponder. This relative range was then combined with direction of arrival information and LBL field component position information to determine an absolute position of the REMUS 100 ranger. The outcome was the demonstration of a passive USBL based tracking system.
Show less
Date Issued: 2013
PURL: http://purl.flvc.org/fcla/dt/3361057
Subject Headings: Underwater acoustic telemetry, Acoustic velocity meters, Array processors, Acoustical engineering, Adaptive signal processing
Format: Document (PDF)

Title: The adhesive effects in dental restoration.
Creator: Vargas, Raul., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: The dental field shows proliferation in the market of new adhesives. The purpose of this study is to evaluate the mechanical properties on total restoration, based on the manufacturer's technical specifications, experimental and mechanical test results. The optimal dentist's selection will be when the most appropriate adhesive can be chosen for one specific restoration, avoiding wasted time, material and exposure to marginal infections with a failure restoration. This research was developed...
Show moreThe dental field shows proliferation in the market of new adhesives. The purpose of this study is to evaluate the mechanical properties on total restoration, based on the manufacturer's technical specifications, experimental and mechanical test results. The optimal dentist's selection will be when the most appropriate adhesive can be chosen for one specific restoration, avoiding wasted time, material and exposure to marginal infections with a failure restoration. This research was developed in stages. The first step is the study of the tooth morphological information. Following, there is the structure identification type and the chemical composition of six different pure adhesives. Next, perform the X-R Diffraction, Energy Disperse Spectroscopy (EDS), and Scanning Electron Microscopy (SEM). The final step is to perform the mechanical test, computer simulation, and discuss the results to obtain the best dental adhesive with and the new finding. Result: The samples show an amorphous structure and a chemical composition in the X-R Diffraction, SEM and EDS experiments. The mechanical test shows real mechanical properties under tension and sheer rupture stress. Poisson ratio, strain, and another relationship will be used in the computer simulation test. Results will be reflected in the Discussion and Conclusion. Significance: The first conclusion is that the amorphous structure is present in all six adhesives experiments. In addition, it shows strong possibilities of bonding with another neighbor's molecules. The discussion will be extended to the bonding advantages for this type of structure in the total dental restoration., Findings: First, we found that the time delay of photo polymerization was controlled with the variable water evaporation of the etching treatment. In addition, it was found that the variable size of the wavelength of the curing light obtained better molecular organization and avoided internal stress and bonding defect. Lastly, the chemical composition was a variable that provided the opportunity to predict the type of bond and strength.
Show less
Date Issued: 2008
PURL: http://purl.flvc.org/fcla/dt/177014
Subject Headings: Dental adhesives, Fillings (Dentistry), Polymers in medicine, Dental bonding
Format: Document (PDF)

Title: Aerodynamic analysis of a propeller in a turbulent boundary layer flow.
Creator: Lachowski, Felipe Ferreira., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Simulating the exact chaotic turbulent flow field about any geometry is a dilemma between accuracy and computational resources, which has been continuously studied for just over a hundred years. This thesis is a complete walk-through of the entire process utilized to approximate the flow ingested by a Sevik-type rotor based on solutions to the Reynolds Averaged Navier-Stokes equations (RANS). The Multiple Reference Frame fluid model is utilized by the code of ANSYS-FLUENT and results are...
Show moreSimulating the exact chaotic turbulent flow field about any geometry is a dilemma between accuracy and computational resources, which has been continuously studied for just over a hundred years. This thesis is a complete walk-through of the entire process utilized to approximate the flow ingested by a Sevik-type rotor based on solutions to the Reynolds Averaged Navier-Stokes equations (RANS). The Multiple Reference Frame fluid model is utilized by the code of ANSYS-FLUENT and results are validated by experimental wake data. Three open rotor configurations are studied including a uniform inflow and the rotor near a plate with and without a thick boundary layer. Furthermore, observations are made to determine the variation in velocity profiles of the ingested turbulent flow due to varying flow conditions.
Show less
Date Issued: 2013
PURL: http://purl.flvc.org/fcla/dt/3360798
Subject Headings: Acoustical engineering, Boundary layer control, Multiphase flow, Mathematical models, Fluid mechanics, Mathematical models, Turbulence, Mathematical models, Computatioinal fluid dynamics
Format: Document (PDF)

Title: Analysis of ship hull and plate vibrations caused by wave forces.
Creator: Lakitosh, Fnu, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: In the present dissertation, the hydrodynamic and hydro-elastic characteristics of ship hull and plate vibrations are analyzed using theoretical and numerical methods. The wave forces are determined using a suite of methods which include the Froude-Krylov method for incident wave forces, Wagner's method and ABS rules for the slamming wave force, and numerical methods for nonlinear wave radiation forces. Finite difference methods are developed to determine the wave forced vibrations of ship...
Show moreIn the present dissertation, the hydrodynamic and hydro-elastic characteristics of ship hull and plate vibrations are analyzed using theoretical and numerical methods. The wave forces are determined using a suite of methods which include the Froude-Krylov method for incident wave forces, Wagner's method and ABS rules for the slamming wave force, and numerical methods for nonlinear wave radiation forces. Finite difference methods are developed to determine the wave forced vibrations of ship hull plates which are modeled using a range of plate theories including nonlinear plate theory with and without material damping and orthotropic plate theory for stiffened hull plates. For small amplitude deformation of thin plates, a semi-theoretical superposition method is used to determine the free and forced vibrations. The transient ship hull vibration due to whipping is also analyzed using the finite difference method. Results, in the form of deformations and stress distributions, are obtained for a range of scantling and wave parameters to identify key parameters to consider in ship structural design.
Show less
Date Issued: 2012
PURL: http://purl.flvc.org/FAU/3342196
Subject Headings: Vibration (Marine engineering), Hulls (Naval architecture), Ships, Hydraulic impact, Ocean waves, Mathematical models, Fluid dynamics, Mathematical models
Format: Document (PDF)

Title: Berth scheduling in container terminals: a pro-active approach to address uncertainties in arrival and handling times.
Creator: Portal Palomo, Maria I., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Ports and container terminals have very complex and dynamic operations. Effective and efficient berth schedules are essential for profitable and sustainable operations. This research studies berth scheduling under uncertainties in arrival and handling times. Port operators usually face challenges in the development of berth schedules. This thesis presents a model formulation of discrete berth space that accounts for uncertainty in arrival and handling times. The problem is reformulated as a...
Show morePorts and container terminals have very complex and dynamic operations. Effective and efficient berth schedules are essential for profitable and sustainable operations. This research studies berth scheduling under uncertainties in arrival and handling times. Port operators usually face challenges in the development of berth schedules. This thesis presents a model formulation of discrete berth space that accounts for uncertainty in arrival and handling times. The problem is reformulated as a biobjective bi-level optimization berth scheduling problem. A solution approach is presented using evolutionary algorithms and heuristics. The objective of the formulation is to provide a robust berth schedule by minimizing the average and the range of the total service times for all vessels served at the terminal. Simulation is utilized to evaluate the proposed berth scheduling policy and compare it to two first-come-first-served policies. Results showed that the proposed berth schedules outperform under high congestion.
Show less
Date Issued: 2013
PURL: http://purl.flvc.org/fcla/dt/3360960
Subject Headings: Container terminals, Management, Marine terminals, Management, Transportation, Planning, Freight and freightage
Format: Document (PDF)

Title: Boundary reflection coefficient estimation from depth dependence of the acoustic Green's function.
Creator: Conrad, Alexander., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Sound propagation in a waveguide is greatly dependent on the acoustic properties of the boundaries. The effect of these properties can be described by a bottom reflection coefficient RB, and surface reflection coefficient RS. Two methods for estimating reflection coefficients are used in this research. The first, the ratio method, is based on the variations of the Green's function with depth utilizing the ratio of the wavenumber spectra at two depths. The second, the pole method, is based on...
Show moreSound propagation in a waveguide is greatly dependent on the acoustic properties of the boundaries. The effect of these properties can be described by a bottom reflection coefficient RB, and surface reflection coefficient RS. Two methods for estimating reflection coefficients are used in this research. The first, the ratio method, is based on the variations of the Green's function with depth utilizing the ratio of the wavenumber spectra at two depths. The second, the pole method, is based on the wavenumbers of the modal peaks in the spectrum at a particular depth. A method to invert for sound speed and density is also examined. Estimates of RB and RS based on synthetic data by the ratio method were very close to their predicted values, especially for higher frequencies and longer apertures. The pole method returned less precise estimates though with longer apertures, the estimates were better. Using experimental data, results of the pole method as well a geoacoustic inversion technique based on them were mixed. The ratio method was used to estimate RS based on the actual data and returned results close to the predicted phase of p.
Show less
Date Issued: 2010
PURL: http://purl.flvc.org/FAU/3164094
Subject Headings: Underwater acoustics, Acoustic surface waves, Green's functions, Electromagnetic waves, Mathematics, Wave equation, Numerical solutions
Format: Document (PDF)

Title: Carbon fiber/vinylester composites in the marine environment: EIS as a means of determining an effective composite interface.
Creator: Vinci, Chris J., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: In this research, the degradation of carbon fiber/vinylester composites in marine environments was experimentally investigated. Additionally, two types of carbon fiber surface treatments, namely Polyhedral Oligomeric Silsesquioxane (POSS) and the industrial surface treatment F0E, were evaluated to determine their effectiveness in creating a fiber/matrix (F/M) interface for use in the marine environment. Electrochemical Impedance Spectroscopy (EIS) was explored as a new application of an...
Show moreIn this research, the degradation of carbon fiber/vinylester composites in marine environments was experimentally investigated. Additionally, two types of carbon fiber surface treatments, namely Polyhedral Oligomeric Silsesquioxane (POSS) and the industrial surface treatment F0E, were evaluated to determine their effectiveness in creating a fiber/matrix (F/M) interface for use in the marine environment. Electrochemical Impedance Spectroscopy (EIS) was explored as a new application of an existing technique for use in measuring the amount of water at the F/M interface in carbon fiber/vinylester composites. EIS spectra were used to determine equivalent electric circuit models that allow for the prediction of water at the interface. The location of water within the composite was determined through Positron Annihilation Lifetime Spectroscopy (PALS). Interlaminar shear strength and transverse tensile tests were carried out for dry conditions and after hygrothermal exposure of the composites to study the influence of the integrity of the F/M interface on the macroscopic response of the composite.
Show less
Date Issued: 2010
PURL: http://purl.flvc.org/FAU/1930500
Subject Headings: Composite materials, Mechanical properties, Graphite fibers, Fibrous composites, Structural analysis
Format: Document (PDF)

Title: Characterizing magnetic noise of AUV for use in towed magnetometer study of internal waves.
Creator: Tilley, Dylan., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: As part of a project to study internal waves, FAU plans to utilize an AUV to tow a magnetometer to study electromagnetic signatures from internal waves. This research is focused on the electromagnetic noise issues related to using an AUV to tow the magnetic sensor package. There are active sources of electromagnetic noise caused by an AUV that are present in addition to those induced by the Earth's magnetic field and permanent magnets. To characterize the magnetic noise associated with the...
Show moreAs part of a project to study internal waves, FAU plans to utilize an AUV to tow a magnetometer to study electromagnetic signatures from internal waves. This research is focused on the electromagnetic noise issues related to using an AUV to tow the magnetic sensor package. There are active sources of electromagnetic noise caused by an AUV that are present in addition to those induced by the Earth's magnetic field and permanent magnets. To characterize the magnetic noise associated with the AUV magnetometer tow system, the various active source elements were identified, the orientation sensitivity of the sensors being used was determined, and the magnetic anomaly of a similar AUV which may be eventually be used in a magnetic sensing arrangement was measured. The results are used to show the proposed sensing arrangement will likely not achieve the necessary sensitivity to measure subtle internal wave signals.
Show less
Date Issued: 2012
PURL: http://purl.flvc.org/FAU/3352881
Subject Headings: Automatic control, Mathematical models, Electromagnetic measurements, Fluctuations (Physics), Oceanographic submersibles, Underwater acoustics
Format: Document (PDF)

Title: Coating selection process for Gulf Stream hydroturbines.
Creator: Bak, Andrew Spicer., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: The study addresses the coating selection for a proposed placement of a hydroturbine into the Gulf Stream. The turbine will generate energy in a similar manner to a wind turbine. The effects of biofouling and corrosion in the current project are assessed. A review of different types of traditional paint coatings is given, as well as the option for a copper-nickel alloy. Testing that should be undertaken for the coating selection is described in detail. Coating considerations are offered and...
Show moreThe study addresses the coating selection for a proposed placement of a hydroturbine into the Gulf Stream. The turbine will generate energy in a similar manner to a wind turbine. The effects of biofouling and corrosion in the current project are assessed. A review of different types of traditional paint coatings is given, as well as the option for a copper-nickel alloy. Testing that should be undertaken for the coating selection is described in detail. Coating considerations are offered and discussed. Design considerations and modifications are also offered.
Show less
Date Issued: 2009
PURL: http://purl.flvc.org/FAU/368607
Subject Headings: Hydraulic turbines, Materials, Testing, Coatings, Thermal properties, Protective coatings
Format: Document (PDF)

Title: Complete thermal design and modeling for the pressure vessel of an ocean turbine -: a numerical simulation and optimization approach.
Creator: Kaiser, Khaled., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: This thesis is an approach of numerical optimization of thermal design of the ocean turbine developed by the Centre of Ocean Energy and Technology (COET). The technique used here is the integrated method of finite element analysis (FEA) of heat transfer, artificial neural network (ANN) and genetic algorithm (GA) for optimization purposes.
Date Issued: 2009
PURL: http://purl.flvc.org/FAU/369194
Subject Headings: Thermal analysis, Computer programs, Heat exchangers, Design and construction, Marine turbines, Testing, Mathematical models, Fluid dynamics
Format: Document (PDF)

Title: Concrete diffusivity and its correlation with chloride deposition rate on concrete exposed to marine environments.
Creator: Echevarria, Victor Anthony., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: The aim of this study was to investigate the diffusion of chloride ions into concrete samples that were exposed in scenarios that simulate the splash, tidal, atmospheric, and immersed portions of a marine structure. To study the atmospheric deposition, the project also investigated the relationship between chloride ion deposition on the wet candle and its accumulation into concrete samples. Results from the wet candle experiment indicated that between 2% and 45% of the chlorides deposited per...
Show moreThe aim of this study was to investigate the diffusion of chloride ions into concrete samples that were exposed in scenarios that simulate the splash, tidal, atmospheric, and immersed portions of a marine structure. To study the atmospheric deposition, the project also investigated the relationship between chloride ion deposition on the wet candle and its accumulation into concrete samples. Results from the wet candle experiment indicated that between 2% and 45% of the chlorides deposited per square meter of exposed area could be found within the concrete samples. After 6 months, slag G1a blocks showed the most resistance to chloride penetration in the tidal and splash simulations. After 10 months of exposure, fly ash samples had the slowest rates of diffusion in the tidal simulation while the fly ash + silica fume samples and the slag samples measured similar rates of diffusion within the tidal zone. After 90 days of curing, cylinders composed of 20% fly ash & 8% silica fume measured the highest average resistivity values and were found to be less vulnerable to chloride ion penetration than the 20% fly ash and the 50% slag concrete through rapid migration tests.
Show less
Date Issued: 2012
PURL: http://purl.flvc.org/FAU/3358557
Subject Headings: Reinforced concrete, Construction, Corrosion, Composite reinforced concrete, Corrosion, Testing, Concrete, Fluid dynamics, Concrete, Chemical resistance, Chlorides, Diffusion rate
Format: Document (PDF)

Title: Concrete surface resistivity profiles along the splash zone on bridge piles exposed to sea water.
Creator: Suarez-Solano, Andres M., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Prevention of the corrosion of steel reinforcement embedded in concrete is a constant challenge in engineering. A study of concrete surface resistivity versus elevation of partially immersed reinforced concrete structures in a marine splash zone has been developed and correlations made between concrete quality and chloride diffusion, i.e., aggressive ion permeability. A conditioning procedure was developed in which the concrete moisture content is increased by direct contact with fresh water...
Show morePrevention of the corrosion of steel reinforcement embedded in concrete is a constant challenge in engineering. A study of concrete surface resistivity versus elevation of partially immersed reinforced concrete structures in a marine splash zone has been developed and correlations made between concrete quality and chloride diffusion, i.e., aggressive ion permeability. A conditioning procedure was developed in which the concrete moisture content is increased by direct contact with fresh water for several days. The electrical resistivity of concrete is known to be primarily a function of the degree of water saturation. Correlations between field obtained concrete surface resistivity values versus chloride diffusivity, and between normalized resistivity measured on cores obtained from the field versus chloride diffusivity has been established. The resistivity values were measured on structures with different concrete mixes and various ages.
Show less
Date Issued: 2009
PURL: http://purl.flvc.org/FAU/369390
Subject Headings: Reinforced concrete, Corrosion, Testing, Reinforcing bars, Properties, Concrete, Permeability, Concrete, Fluid dynamics
Format: Document (PDF)

Title: Corrosion initiation and propagation on corrosion resistant alloys embedded in concrete by accelerated chloride transport.
Creator: Gutierrez Tellez, Francisco., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Two duplex stainless steels rebars: UNS32304SS and UNS32101SS, were selected to investigate the corrosion initiation and propagation in reinforced concrete specimens. The investigation is divided in two phases with two different methods to accelerate the transport of chlorides through the concrete and initiate corrosion in a short period of time. After corrosion had initiated and propagated for some time; selected specimens were terminated for visual examination. On specimens selected for...
Show moreTwo duplex stainless steels rebars: UNS32304SS and UNS32101SS, were selected to investigate the corrosion initiation and propagation in reinforced concrete specimens. The investigation is divided in two phases with two different methods to accelerate the transport of chlorides through the concrete and initiate corrosion in a short period of time. After corrosion had initiated and propagated for some time; selected specimens were terminated for visual examination. On specimens selected for autopsy, the rebars in the top row showed corrosion to various degrees. Corrosion had propagated to such extent on the terminated specimens that the specimen showed cracks. Stray current might have caused accelerated corrosion on rebars where corrosion had initiated. Based on chloride concentrations measured at the rebar trace, corrosion initiated: on S32101 rebars on average at 7.9 kg/m3, and S32101 rebars on average at 6.0 kg/m3. The findings suggest that S32304 rebars corroded at a slower than S32101.
Show less
Date Issued: 2013
PURL: http://purl.flvc.org/fcla/dt/3362380
Subject Headings: Concrete, Corrosion, Concrete construction, Reinforced concrete, Chemical resistance, Steel, Structural, Corrosion
Format: Document (PDF)

Title: Degradation of mechanical properties of vinylester and carbon fiber/vinylester composites due to environmental exposure.
Creator: Figliolini, Alexander M., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: An experimental investigation was undertaken to determine the effects of marine environmental exposure on the mechanical properties of vinylester resins (VE510A and VE8084) and carbon fiber/VE510A vinylester composites. The effect of carbon fiber sizing on the composite strengths was also examined. Neat resins were exposed to marine environments until moisture content reached a point of saturation after which they were tested in tension, compression and shear. Compared to the baseline dry...
Show moreAn experimental investigation was undertaken to determine the effects of marine environmental exposure on the mechanical properties of vinylester resins (VE510A and VE8084) and carbon fiber/VE510A vinylester composites. The effect of carbon fiber sizing on the composite strengths was also examined. Neat resins were exposed to marine environments until moisture content reached a point of saturation after which they were tested in tension, compression and shear. Compared to the baseline dry specimens, specimens subjected to moisture showed overall increased ductility and a reduction in strength. Dry and moisture saturated composite specimens were tested in tension and compression in different orientations. Longitudinal specimens were tested in in-plane shear and interlaminar shear. Composites with F-sized carbon fibers displayed overall higher strength than those with G-sized fibers at both dry and moisture saturated conditions. An analysis of moisture absorption of the composites was performed which vii shows that the moisture up-take is dominated by the fiber/matrix region which absorbs up to 90% of the moisture. The composites experienced reduced strength after moisture absorption. The results revealed that the fiber sizing has stronger effect on the fiber/matrix interface dominated strengths than moisture up-take.
Show less
Date Issued: 2011
PURL: http://purl.flvc.org/FAU/3332182
Subject Headings: Composite materials, Mechanical properties, Polymers, Deterioration, FIbrous composites, Graphite fibers
Format: Document (PDF)

Title: Degradation of the composite fiber/matrix interface in marine environment.
Creator: Farooq, Muhammad Umar., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Durability of the composite materials in marine environments has been investigated experimentally and with analytical and numerical methods. The main focus of this study is on the integrity of the fiber/matrix interface under seawater exposure. A single-fiber compression test specimen called the Outwater-Murphy (OM) test has been analyzed using mechanics of materials principles and linear elastic fracture mechanics. Sizing of the OM specimen was conducted so that debonding of the fiber from...
Show moreDurability of the composite materials in marine environments has been investigated experimentally and with analytical and numerical methods. The main focus of this study is on the integrity of the fiber/matrix interface under seawater exposure. A single-fiber compression test specimen called the Outwater-Murphy (OM) test has been analyzed using mechanics of materials principles and linear elastic fracture mechanics. Sizing of the OM specimen was conducted so that debonding of the fiber from the interface should be achieved prior to yielding of the matrix and global instability failure. Stress analysis of the OM specimen has been conducted from theory of elasticity and finite element analysis. A superelement technique was developed for detailed analysis of the stress state at the fiber/matrix interface. The interface stress state at the debond site in the OM specimen, i.e. at the hole edge, was identified as biaxial tension at the fiber/matrix interface. Characterization of cure and post-cure of 8084 and 510A vinlyester resins has been performed using cure shrinkage tests based on dynamic mechanical analysis and coated beam experiments. In addition, moisture absorption, swelling and the influence of moisture on the mechanical properties of the resins were determined. Testing of OM specimens consisting of a single carbon or glass fiber embedded in vinylester resin at dry conditions and after seawater exposure revealed that the debond toughness was substantially reduced after exposure of the OM specimen to seawater. C(F) did not debond. Macroscopic carbon/vinylester woven composites where the fibers were sized with F sizing were tested in shear at dry conditions and after four weeks of seawater exposure. The shear strength was very little affected after the short immersion time.
Show less
Date Issued: 2009
PURL: http://purl.flvc.org/FAU/228774
Subject Headings: Fibrous composites, Graphite fibers, Composite materials, Mechanical properties, Polymers, Deterioration
Format: Document (PDF)

Title: Design & performance of a wind and solar-powered autonomous surface vehicle.
Creator: Rynne, Patrick Forde., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: The primary objective of this research is the development a wind and solar-powered autonomous surface vehicle (WASP) for oceanographic measurements. This thesis presents the general design scheme, detailed aerodynamic and hydrodynamic aspects, sailing performance theory, and dynamic performance validation measurements obtained from a series of experiments. The WASP consists of a 4.2 meter long sailboat hull, a low-Reynolds number composite wing, a 2000 Watt-hour battery reservoir, a system of...
Show moreThe primary objective of this research is the development a wind and solar-powered autonomous surface vehicle (WASP) for oceanographic measurements. This thesis presents the general design scheme, detailed aerodynamic and hydrodynamic aspects, sailing performance theory, and dynamic performance validation measurements obtained from a series of experiments. The WASP consists of a 4.2 meter long sailboat hull, a low-Reynolds number composite wing, a 2000 Watt-hour battery reservoir, a system of control actuators, a control system running on an embedded microprocessor, a suite of oceanographic sensors, and power regeneration from solar energy. The vehicle has a maximum speed of five knots and weighs approximately 350 kilograms. Results from four oceanographic missions that were conducted in the Port Everglades Intracoastal Waterway in Dania Beach [sic] Florida are presented. Water temperature, salinity and oxidation-reduction measurements recorded during these missions are also discussed. The combination of a mono-hull and solid wing in an autonomous system is a viable design for a long-range ocean observation platform. The results of four near-shore ocean observation missions illustrate the initial capabilities of the design. Future work aimed to further reduce both the mass of the wing design and the power requirements of the system will increase performance in all operating conditions and should be considered. Furthermore, the progression of the legal framework related to ocean vehicles must be pursued with respect to unmanned autonomous systems.
Show less
Date Issued: 2008
PURL: http://purl.flvc.org/FAU/166455
Subject Headings: Hydrographic surveying, Instruments, Evaluation, Aids to navigation, Equipment and supplies, Testing, Sailboats, Design and construction, Robots, Control systems, Oceanographic instruments, Evaluation
Format: Document (PDF)

Title: Design and analysis of an ocean current turbine performance assessment system.
Creator: Young, Matthew T., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: This thesis proposes a sensor approach for quantifying the hydrodynamic performance of Ocean Current Turbines (OCT), and investigates the influence of sensor-specific noise and sampling rates on calculated turbine performance. Numerical models of the selected sensors are developed, and then utilized to add stochastic measurement error to numerically-generated, non-stochastic OCT data. Numerically-generated current velocity and turbine performance measurements are used to quantify the relative...
Show moreThis thesis proposes a sensor approach for quantifying the hydrodynamic performance of Ocean Current Turbines (OCT), and investigates the influence of sensor-specific noise and sampling rates on calculated turbine performance. Numerical models of the selected sensors are developed, and then utilized to add stochastic measurement error to numerically-generated, non-stochastic OCT data. Numerically-generated current velocity and turbine performance measurements are used to quantify the relative influence of sensor-specific error and sampling limitations on sensor measurements and calculated OCT performance results. The study shows that the addition of sensor error alters the variance and mean of OCT performance metric data by roughly 7.1% and 0.24%, respectively, for four evaluated operating conditions. It is shown that sensor error results in a mean, maximum and minimum performance metric to Signal to Noise Ration (SNR) of 48.6% and 6.2%, respectively.
Show less
Date Issued: 2012
PURL: http://purl.flvc.org/FAU/3359164
Subject Headings: Marine turbines, Mathematical models, Fluid dynamics, Structural dynamics, Stochastic processes, Rotors, Design and construction, Testing
Format: Document (PDF)

Mathematical models (27)	+ -
Fluid dynamics (21)	+ -
Testing (20)	+ -
Design and construction (16)	+ -
Composite materials (14)	+ -

Marine turbines (11)	+ -
Structural dynamics (10)	+ -
Renewable energy sources (9)	+ -
Underwater acoustics (9)	+ -
Computational fluid dynamics (7)	+ -
Mechanical properties (7)	+ -
Adaptive signal processing (6)	+ -
Concrete (6)	+ -
Fluid mechanics (6)	+ -
Reinforced concrete (6)	+ -
Wave motion, Theory of (6)	+ -
Corrosion (5)	+ -
Fibrous composites (5)	+ -
Inertial navigation systems (5)	+ -
Measurement (5)	+ -
Nanostructured materials (5)	+ -
Oceanographic instruments (5)	+ -
Ships (5)	+ -
Turbines (5)	+ -
Acoustical engineering (4)	+ -
Computer simulation (4)	+ -
Digital techniques (4)	+ -
Evaluation (4)	+ -
Hydrodynamics (4)	+ -
Ocean energy resources (4)	+ -

Florida (1)	+ -
Florida, Straits of (1)	+ -
Gulf Stream (1)	+ -
Planning (1)	+ -
United States (1)	+ -

College of Engineering and Computer Science (99)	+ -
Liu, Yanbo. (2)	+ -
Mahfuz, Hassan (2)	+ -
Zbeeb, Khaled. (2)	+ -
Akram, Mohammad Wasim (1)	+ -

Altamirano, Luis. (1)	+ -
Alvarez, Jose L. (1)	+ -
Ananthakrishnan, Palaniswamy (1)	+ -
Asseff, Nicholas S. (1)	+ -
Bak, Andrew Spicer. (1)	+ -
Balasubramanian, Hariharan (1)	+ -
Barousse, Julien. (1)	+ -
Bastiani, Sergio. (1)	+ -
Blanc, Jean-Baptiste. (1)	+ -
Brisson, Lisa Nicole. (1)	+ -
Browning, Grant. (1)	+ -
Bryan, Benjamin Skyler (1)	+ -
Carlson, Edward A. (1)	+ -
Charles E. Schmidt College of Science (1)	+ -
Conrad, Alexander. (1)	+ -
Cribbs, Allison Rose. (1)	+ -
Das, Debdutta. (1)	+ -
Davis, Charles (1)	+ -
Deng, Yueyue (1)	+ -
Dhanak, Manhar R. (1)	+ -
Echevarria, Victor Anthony. (1)	+ -
Farooq, Muhammad Umar. (1)	+ -
Figliolini, Alexander M. (1)	+ -
Fisher, Aaron D. (1)	+ -

Search In

Pages

Pages

Sort Results By:

Narrow results by:

Collection

Topical Subject

Geographic Subject

Genre Subject

Genre

Type of Resource

Language

Creator

Format