Current Search: Ship propulsion (x)
View All Items
- Title
- Flow visualization of the ventilated cavities generated by a surface piercing propeller.
- Creator
- Altamirano, Luis., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
- Abstract/Description
-
In the present study, 3 wake parameters are semi-automatically measured in 63 composite-labeled images of a surface piercing propeller tested at yaw angles 0-30 degrees, pitch angles 0-15 degrees, propeller immersion ratios of 0.33 and 0.50 and scaled advance ratios 0.656-1.927. A fourth wake parameter is measured in four composite labeled images of yaw angles 0-30 degrees, pitch angle 0 degrees, immersion ratios of 0.33 and 0.50 and scaled advance ratios 1.363-1.927. Measurements are plotted...
Show moreIn the present study, 3 wake parameters are semi-automatically measured in 63 composite-labeled images of a surface piercing propeller tested at yaw angles 0-30 degrees, pitch angles 0-15 degrees, propeller immersion ratios of 0.33 and 0.50 and scaled advance ratios 0.656-1.927. A fourth wake parameter is measured in four composite labeled images of yaw angles 0-30 degrees, pitch angle 0 degrees, immersion ratios of 0.33 and 0.50 and scaled advance ratios 1.363-1.927. Measurements are plotted against propeller's angular position. Major findings include the behavior of wake parameters as the values of scaled advance ratio, yaw angle, pitch angle, and immersion ratio vary.
Show less - Date Issued
- 2010
- PURL
- http://purl.flvc.org/FAU/1927299
- Subject Headings
- Ships, Hydrodynamics, Ship propulsion
- Format
- Document (PDF)
- Title
- Open water testing of a surface piercing propeller with varying submergence, yaw angle and inclination angle.
- Creator
- Lorio, Justin M., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
- Abstract/Description
-
The use of surface piercing propellers (SPPs) shows promise for high speed operation by virtually eliminating appendage drag, which can be as much as 30 percent of the total drag on a vehicle at high speeds. The scarcity of available systematic test data has made reliable performance prediction difficult. The primary objective of this research is to obtain experimental performance prediction data that can be used in SPP design. In a series of open water tests in a non-pressurized towing tank...
Show moreThe use of surface piercing propellers (SPPs) shows promise for high speed operation by virtually eliminating appendage drag, which can be as much as 30 percent of the total drag on a vehicle at high speeds. The scarcity of available systematic test data has made reliable performance prediction difficult. The primary objective of this research is to obtain experimental performance prediction data that can be used in SPP design. In a series of open water tests in a non-pressurized towing tank facility, force transducer measurements were taken at tip immersion ratios from 0.5 to .33, yaw angles from 0° to 30° and inclination angles from 0° to 15° over a range of advance ratios from 0.8 to 1.8. Force transducer measurements were taken for thrust, torque, side forces and moments. These results will help develop a baseline for the verification of SPP performance prediction.
Show less - Date Issued
- 2010
- PURL
- http://purl.flvc.org/FAU/1930498
- Subject Headings
- Ships, Hydrodynamics, Ship propulsion, Propellers
- Format
- Document (PDF)
- Title
- A direct thrust measurement system for a waterjet propelled, free running USV.
- Creator
- Grimes, John A., von Ellenrieder, Karl, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
- Abstract/Description
-
The relationship between cross-flow at a waterjet inlet and delivered thrust is not fully understood. A direct thrust measurement system was designed for a waterjet propelled, free running USV. To induce sway velocity at the waterjet inlet, which was considered equivalent to the cross flow, circles of varying radii were performed at Reynolds Numbers between 3.48 x 106 and 8.7 x 106 and radii from 2.7 to 6.3 boat lengths. Sway velocities were less than twenty percent of mean forward speed with...
Show moreThe relationship between cross-flow at a waterjet inlet and delivered thrust is not fully understood. A direct thrust measurement system was designed for a waterjet propelled, free running USV. To induce sway velocity at the waterjet inlet, which was considered equivalent to the cross flow, circles of varying radii were performed at Reynolds Numbers between 3.48 x 106 and 8.7 x 106 and radii from 2.7 to 6.3 boat lengths. Sway velocities were less than twenty percent of mean forward speed with slip angles that were less than 20°. Thrust Loading Coefficients were compared to sway as a percent of forward speed. In small radius turns, no relationship was seen, while in larger radius turns, peaks of sway velocity corresponded with drops in thrust, but this was determined to be caused by reduced vehicle yaw in these intervals . Decoupling of thrust and yaw rate is recommended for future research.
Show less - Date Issued
- 2013
- PURL
- http://purl.flvc.org/fau/fd/FA0004023
- Subject Headings
- Oceanographic instruments -- Evaluation, Propellers, Ship propulsion, Ships -- Hydrodynamics, Stability of ships
- Format
- Document (PDF)
- Title
- Investigation of marine waterjet inlets during turning maneuvers.
- Creator
- Duerr, Phillip S., von Ellenrieder, Karl, Florida Atlantic University, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
- Abstract/Description
-
Numerical simulations of waterjet inlets have been conducted in order to understand inlet performance during ship turning maneuvers. During turning maneuvers waterjet systems may experience low efficiency, cavitation, vibration, and noise. This study found that during turns less energy arrived at the waterjet pump relative to operating straight ahead, and that the flow field at the entrance of the waterjet pump exhibited a region of both low pressure and low axial velocity. The primary reason...
Show moreNumerical simulations of waterjet inlets have been conducted in order to understand inlet performance during ship turning maneuvers. During turning maneuvers waterjet systems may experience low efficiency, cavitation, vibration, and noise. This study found that during turns less energy arrived at the waterjet pump relative to operating straight ahead, and that the flow field at the entrance of the waterjet pump exhibited a region of both low pressure and low axial velocity. The primary reason for the change in pump inflow uniformity is due to a streamwise vortex. In oblique inflow the hull boundary layer separates when entering the inlet and wraps up forming the streamwise vortex. These changes in pump inflow during turning maneuvers will result in increased unsteady loading of the pump rotor and early onset of pump rotor cavitation.
Show less - Date Issued
- 2015
- PURL
- http://purl.flvc.org/fau/fd/FA00004364, http://purl.flvc.org/fau/fd/FA00004364
- Subject Headings
- Fluid dynamics, Ships--Hydrodynamics, Ships--Maneuverability--Simulation methods, Ship handling--Simulation methods, Ship propulsion, Stability of ships, Oceanographic instruments--Evaluation
- Format
- Document (PDF)
- Title
- Electric motor control system with application to marine propulsion.
- Creator
- Roa, Camilo Carlos, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
- Abstract/Description
-
This thesis analyses the behavior of an induction motor based on a mathematical model created for its simulation. The model describes the interaction of its several non linear differential equations to present a simulated output of induced torque and mechanical speed. Considering the applications to marine propulsion, it is also the goal of the project to design and test a control system for the speed of the motor by maintaining a specific cruse speed regardless the perturbations.
- Date Issued
- 2010
- PURL
- http://purl.flvc.org/FAU/2705080
- Subject Headings
- Electric motors, Induction, Electric propulsion, Field orientation principle (Electric engineering), Ships, Hydrodynamics
- Format
- Document (PDF)