View All Items

Title: Chloride Diffusivity and Aging Factor Determined on Field Simulated Concrete Exposed to Seawater.
Creator: Raof, Farhad Fakheri, Presuel-Moreno, Francisco, Florida Atlantic University, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Chloride diffusivity in high performance concrete is influenced by the exposure environment, aside from the concrete mixture properties like, water to cementitious ratio (w/cm) and presence of add-on pozzolans. In this study, a set of concrete specimens (eleven-different concrete mixtures) were cast and exposed to three different environmental conditions (Tidal, Splash and Barge) in which the solution was seawater or brackish water. These exposures simulated environmental field conditions....
Show moreChloride diffusivity in high performance concrete is influenced by the exposure environment, aside from the concrete mixture properties like, water to cementitious ratio (w/cm) and presence of add-on pozzolans. In this study, a set of concrete specimens (eleven-different concrete mixtures) were cast and exposed to three different environmental conditions (Tidal, Splash and Barge) in which the solution was seawater or brackish water. These exposures simulated environmental field conditions. After the specimens had been wet cured for 32 days (on average), the specimens were exposed to three different field simulation conditions for up to 54 months. The specimens under the field simulated conditions were cored at 6, 10, 18, 30 and 54 months at four elevations and then the chloride profiles were obtained from the cores. The apparent diffusivity values for each profile were calculated based on Fick’s 2nd law. Then, the aging factor “m” was calculated by regression analysis of the diffusivity values vs. time (days) plotted in the log10-log10 scale. This was done for samples exposed to the three different exposure conditions and then the results were compared side-by-side. First, the “m” values were calculated using the exposure duration. Then, to study the effect of including the curing time on “m” value, the curing time was added to the exposure time and a new calculation and “m” value was obtained and compared with the previous results. Moreover, upon inspecting the chloride diffusivity values vs. time plots, it was observed that in some cases, a number of data points showed significantly higher or lower values in comparison with the rest of the data points. It was decided to recalculate the “m” values for these cases, and to only use selected data points instead of all data points (i.e., remove outlier data points). In terms of chloride diffusivity value, it was found that in most cases the specimens with higher water to cementitious (w/cm) ratio showed higher diffusivity, as expected. Further, the presence of pozzolans had a noticeable impact on the chloride diffusivity by decreasing the diffusion rate due to microstructure changes that occurred with time. In terms of “m” values, the result for the field simulated conditions showed a range of “m” values dependent on the specimen’s mixture composition and the elevation at which the specimens were cored. It was observed that the chloride diffusivity declined with time and after a certain amount of time (in this research, almost after 30 months) the diffusivity reduction became small and a transition in the slope of the diffusivity trend appeared in a number of cases. After the transition, the diffusivity trend reached either a plateau zone or continued with a significantly lower slope, depending on the time, composition and exposure. It was found that the specimens under tidal and splash field simulation conditions that had only fly ash in their mixtures showed higher “m” values when compared with samples that contained fly ash and silica fume or fifty percent slag.
Show less
Date Issued: 2019
PURL: http://purl.flvc.org/fau/fd/FA00013254
Subject Headings: Concrete--Environmental testing, Seawater, Chlorides, Diffusion, Concrete--Deterioration
Format: Document (PDF)

Title: Microbial Induced Degradation in Synthetic Fiber Reinforced Concrete Samples in South Florida.
Creator: Parkinson, Jacqueline Cecile, Presuel-Moreno, Francisco, Florida Atlantic University, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Synthetic fiber reinforced concrete sample sets were exposed to two different environments. One set, of six samples, was exposed to filtered seawater in the lab with wet and dry cycles, while the other set of samples was exposed, on a barge, to the marine environment, in the intracoastal waterways, at SeaTech. The samples were exposed for 8 months, and then removed for experimental and mechanical testing. Upon removal, the barge samples were photographed to observe surface organisms that were...
Show moreSynthetic fiber reinforced concrete sample sets were exposed to two different environments. One set, of six samples, was exposed to filtered seawater in the lab with wet and dry cycles, while the other set of samples was exposed, on a barge, to the marine environment, in the intracoastal waterways, at SeaTech. The samples were exposed for 8 months, and then removed for experimental and mechanical testing. Upon removal, the barge samples were photographed to observe surface organisms that were attached to each sample. The barge samples, after cleaning, were then exposed to UV light to observe surface bacteria. The barge samples were also taken to Harbor Branch facility for DNA testing, and then sent in for sequencing. This sequencing was used to identify the organisms that were present inside the concrete samples. An Indirect Tensile Strength Test, IDT, was performed on both sets of samples to observe the first crack, max load, and fracture toughness of each sample. The Barge samples had a lower first crack, max load, and fracture toughness, which means that it took less force to break these samples, than the Seawater samples. As the fiber content increased, the Seawater samples grew stronger, while the Barge samples grew weaker. Also, as the fiber content increased, the biodiversity found on the surface of the Barge samples increased as well.
Show less
Date Issued: 2019
PURL: http://purl.flvc.org/fau/fd/FA00013251
Subject Headings: Fiber-reinforced concrete, Florida, Concrete--Deterioration, Microbes
Format: Document (PDF)

Title: THE IMPACT CORROSION HAS ON THE DEGRADATION OF MECHANICAL PROPERTIES OF CARBON STEEL REBARS IN HIGH PERFORMANCE CONCRETE.
Creator: Rosa-Pagan, Angel R., Presuel-Moreno, Francisco, Florida Atlantic University, Department of Ocean and Mechanical Engineering, College of Engineering and Computer Science
Abstract/Description: A significant amount of reinforced concrete structures in the USA are reaching the design life span of 50 years. Degradation of these infrastructure due to corrosion presents an economical, safety and quality of life challenge for our society. Being able to study and determine the conditions of our infrastructure, perform maintenance before failure and predict failure before occurrence has become critical for our society and our way of life. This study was performed to add to existing...
Show moreA significant amount of reinforced concrete structures in the USA are reaching the design life span of 50 years. Degradation of these infrastructure due to corrosion presents an economical, safety and quality of life challenge for our society. Being able to study and determine the conditions of our infrastructure, perform maintenance before failure and predict failure before occurrence has become critical for our society and our way of life. This study was performed to add to existing research in the understanding of the relationships between the corrosion current of the embedded carbon steel rebars in reinforced concrete, rebar mass loss due to corrosion and the degradation of the mechanical properties of the carbon steel embedded in high performance concrete structures. The study also aimed to study the influence of different independent variables such as the chloride solution reservoir size and the concrete composition of the prepared specimens for the study. Specimens for the study were prepared by embedding three carbon steel size #4 rebars in blocks of high performing concrete with different admixture to enhance their performance against corrosion. To initiate corrosion specimens were exposed to accelerated chloride transport method (electromigration). To accelerate corrosion some samples were selected for anodic polarization and additional electromigration. After corrosion initiation, the rebars Open Circuit Potential (OCP) and corrosion current (Icorr) were periodically measured using a galvanostat device from April 2017 to August 2021. The OCP average values showed that all the rebars considered in this study were in active corrosion. Faraday’s law was used to determine the rebar calculated mass loss from the measured corrosion current and the elapse time between measurements. The rebar mass loss was in turn used to model the loss of the physical properties of the rebar (yield strength, ultimate strength, and ultimate strain) using (Vanama & Ramakrishnan, 2020) model. Analysis of these parameters results showed a direct relationship between the measured corrosion current and the calculated mass loss of the corroding rebar. The study also showed a direct relationship between the calculated mass loss of the corroding rebar and the degradation of the physical properties of the rebar.
Show less
Date Issued: 2021
PURL: http://purl.flvc.org/fau/fd/FA00013843
Subject Headings: Corrosion, Reinforced concrete--Deterioration, Carbon steel, High strength concrete
Format: Document (PDF)

Title: Influence of direct electrical current upon specific volume of mortar in sea water.
Creator: Le Floch, Anne., Florida Atlantic University, Hartt, William H., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Hollow, cylindrical mortar specimens of 0.4 water-cement ratio were prepared without reinforcement and exposed to flowing natural sea water for periods up to one year. Direct currents of 2, 10 and 50 mA were impressed between a mixed metal-oxide titanium substrate electrode positioned within each of these two zones, with a different electrolyte supply and exhaust for the cylinder core and exterior surface. Linear expansion of the specimens was evaluated as a function of exposure duration from...
Show moreHollow, cylindrical mortar specimens of 0.4 water-cement ratio were prepared without reinforcement and exposed to flowing natural sea water for periods up to one year. Direct currents of 2, 10 and 50 mA were impressed between a mixed metal-oxide titanium substrate electrode positioned within each of these two zones, with a different electrolyte supply and exhaust for the cylinder core and exterior surface. Linear expansion of the specimens was evaluated as a function of exposure duration from the output of embedded strain gages and from dimensional measurement of cylinder length and diameter. It was found that expansion of specimens exposed to direct current exceeded baseline ones (no current). Also, the expansion was anisotropic in that different magnitudes and trends were apparent for the diameter versus length directions. The expansion under free exposure (no current) was determined to be a function of specimen size and of the direction of measurement relative to the cast specimen face.
Show less
Date Issued: 1995
PURL: http://purl.flvc.org/fcla/dt/15214
Subject Headings: Concrete--Deterioration, Concrete--Corrosion, Seawater corrosion, Cathodic protection
Format: Document (PDF)

Title: Bulk diffusion of high performance concrete specimens exposed to different levels of sodium chloride and seawater.
Creator: Arias, Wendy J., Presuel-Moreno, Francisco, Florida Atlantic University, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: The purpose of this study was to investigate the performance to chloride penetration of specimens made with three base compositions (three different supplementary cementitious materials) and water to cementitious ratios of 0.35, 0.41, or 0.47. The specimens were subjected to bulk diffusion test or full immersion. The mixes were exposed to 0.1 M, 0.6 M, or 2.8 M sodium chloride solution for different periods of time. Also, partially immersed specimens were exposed to indoor and outdoor...
Show moreThe purpose of this study was to investigate the performance to chloride penetration of specimens made with three base compositions (three different supplementary cementitious materials) and water to cementitious ratios of 0.35, 0.41, or 0.47. The specimens were subjected to bulk diffusion test or full immersion. The mixes were exposed to 0.1 M, 0.6 M, or 2.8 M sodium chloride solution for different periods of time. Also, partially immersed specimens were exposed to indoor and outdoor exposures (tidal, splash, barge). Chloride concentration profiles were obtained and the apparent diffusion coefficient was calculated. The skin effect was found only on some chloride profiles exposed to 0.1 M sodium chloride solution. The chloride binding capacity was calculated; specimens with 20% Fly Ash and 8% Silica Fume had the highest binding capacity (70.99%). The apparent diffusivity coefficient was found to be dependent on the curing regime as well as the water to cement ratio. The correlation between effective resistivity and apparent diffusion coefficient was determined.
Show less
Date Issued: 2014
PURL: http://purl.flvc.org/fau/fd/FA00004076, http://purl.flvc.org/fau/fd/FA00004076
Subject Headings: Bulk solids flow, Concrete -- Corrosion, Concrete, Effect of salt on, Reinforced concrete -- Deterioration, Sustainable construction
Format: Document (PDF)

Title: Experimental evaluation of cement stucco surfacing material (CSSM) removal for reducing particulates in air.
Creator: Cowan, David, Meeroff, Daniel E., Florida Atlantic University, College of Engineering and Computer Science, Department of Civil, Environmental and Geomatics Engineering
Abstract/Description: Every year millions of construction workers are exposed to dust in levels that create a hazard to them (Fundukian, 2011). Their environment is contaminated by activities such as cutting, chipping, grinding and sanding building materials. The Occupational Safety and Health Administration (OSHA) refers to this general collection of building materials debris and fine particulates as nuisance dust. Some of the particles in nuisance dust possess properties that make them especially hazardous, such...
Show moreEvery year millions of construction workers are exposed to dust in levels that create a hazard to them (Fundukian, 2011). Their environment is contaminated by activities such as cutting, chipping, grinding and sanding building materials. The Occupational Safety and Health Administration (OSHA) refers to this general collection of building materials debris and fine particulates as nuisance dust. Some of the particles in nuisance dust possess properties that make them especially hazardous, such as their shape or specific gravity. It has been found by the Center for Disease Control (CDC) that inhalation of quantities of silica dust above the permissible exposure limit (15.0 mg/m3) causes a deterioration of the outside lining of the lung.This research seeks to limit this exposure by a pretreatment process using acid application and then absorbed moisture content that reduces airborne particulate during the removal of cement stucco surfacing materials. Successful pretreatment would allow removal of CSSM from substrates such that the release of airborne particulates does not exceed the permissible exposure limits (PEL) found in the 29 CFR-Table Z-3 for mining applications (15-mg/m3).
Show less
Date Issued: 2015
PURL: http://purl.flvc.org/fau/fd/FA00004438, http://purl.flvc.org/fau/fd/FA00004438
Subject Headings: Air -- Pollution -- United States -- Measurement, Air quality management, Concrete -- Deterioration, Environmental health, Particles -- Environmental aspects
Format: Document (PDF)

Title: Accelerated corrosion of steel in dry-cast reinforced concrete pipes after initiation.
Creator: Weber, Brian W., Presuel-Moreno, Francisco, Florida Atlantic University, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Instrumented dry-cast reinforced concrete pipe (DC-RCP) specimens in which corrosion of the reinforcing steel had initiated were selected to accelerate the corrosion. Type C and type F DC-RCP were used. An anodic current density of various magnitudes (0.5 μA/cm2, 1 μA/cm2 and 2.5 μA/cm2) was applied during the corrosion propagation stage. The specimens were placed in high humidity and selected specimens were later covered with wet sand. Selected specimens were terminated for visual...
Show moreInstrumented dry-cast reinforced concrete pipe (DC-RCP) specimens in which corrosion of the reinforcing steel had initiated were selected to accelerate the corrosion. Type C and type F DC-RCP were used. An anodic current density of various magnitudes (0.5 μA/cm2, 1 μA/cm2 and 2.5 μA/cm2) was applied during the corrosion propagation stage. The specimens were placed in high humidity and selected specimens were later covered with wet sand. Selected specimens were terminated for visual examination and gravimetric analysis. Typically, the reinforcement potentials during the accelerated corrosion period were more negative for F specimens compared to C specimens. The C specimens experienced ~2× more corrosion than the F specimens. The accumulated corrosion products did not cause cracks. A method was developed that allows for modest corrosion acceleration during the corrosion propagation stage of DC-RCP.
Show less
Date Issued: 2014
PURL: http://purl.flvc.org/fau/fd/FA00004233, http://purl.flvc.org/fau/fd/FA00004233
Subject Headings: Concrete -- Deterioration, Corrosion and anti corrosives, Pipelines -- Design and construction, Tubular steel structures -- Deterioration
Format: Document (PDF)

Title: Initiation and propagation of corrosion in dry-cast reinforced concrete ring specimens.
Creator: Seo, Bongjoon, Presuel-Moreno, Francisco, Florida Atlantic University, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: The corrosion propagation stage of D-CRP (types F and C) was tested under immersion in water, high humidity, and covered with wet sand. The half-cell potential, linear polarization test, and electrochemical impedance spectroscopy measurements were performed. Selected specimens were terminated after 300 days of exposure and visually inspected. Based on corrosion potential measurements obtained during the corrosion propagation observation, and calculated corrosion rate based on LPR measurements...
Show moreThe corrosion propagation stage of D-CRP (types F and C) was tested under immersion in water, high humidity, and covered with wet sand. The half-cell potential, linear polarization test, and electrochemical impedance spectroscopy measurements were performed. Selected specimens were terminated after 300 days of exposure and visually inspected. Based on corrosion potential measurements obtained during the corrosion propagation observation, and calculated corrosion rate based on LPR measurements: all specimens were actively corroding. Additionally, EIS-Rc values were calculated for FS, CS and CH specimens. The Rc_EIS were generally greater than Rc_LPR values. EIS spectra for CI and FI specimens usually included mass transport limitations, as these specimens were immersed. Both type of specimens immersed in water (FI and CI), appeared to have higher corrosion rate based on LPR-Rc. However, upon autopsy it was revealed that a more modest amount of corrosion occurred on the reinforcing steel of FI and CI terminated specimens.
Show less
Date Issued: 2014
PURL: http://purl.flvc.org/fau/fd/FA00004226, http://purl.flvc.org/fau/fd/FA00004226
Subject Headings: Concrete -- Deterioration, Concrete construction, Corrosion and anti corrosives, Reinforced concrete -- Chemical resistance, Tubular steel structures -- Deterioration
Format: Document (PDF)

Title: Cathodic polarization response of simulated prestressed concrete piles exposed to natural sea water.
Creator: Chaix, Olivier., Florida Atlantic University, Hartt, William H.
Abstract/Description: Experiments were conducted to determine the effectiveness of localized cathodic polarization for reducing corrosion of simulated prestressed concrete piles containing admixed calcium chloride and exposed to a simulated sea water tidal cycle. The specimens contained both continuous and segmented steel tendons, the purpose of the latter being to facilitate measurement of cathodic protection current. Conductive rubber in an impressed current system was used as the anode material. The specimens...
Show moreExperiments were conducted to determine the effectiveness of localized cathodic polarization for reducing corrosion of simulated prestressed concrete piles containing admixed calcium chloride and exposed to a simulated sea water tidal cycle. The specimens contained both continuous and segmented steel tendons, the purpose of the latter being to facilitate measurement of cathodic protection current. Conductive rubber in an impressed current system was used as the anode material. The specimens were initially freely corroded and then cathodically polarized at a constant current ranging from 0.5 to 1 mA/m$\sp2$ which corresponded to potentials (current-on) which ranged from $-$0.500 to $-$1.100 V(sce) in the anode region. The magnitude of impressed current and its distribution along the embedded steel was monitored as a function of exposure time, level of polarization and water levels. Current-on and instant-off potential distribution for both the continuous and segmented tendons were also measured. The level of cathodic polarization was assessed as a function of position along the specimens by the depolarization method. The results were evaluated within the context of marine bridge substructure cathodic protection technology.
Show less
Date Issued: 1992
PURL: http://purl.flvc.org/fcla/dt/14865
Subject Headings: Corrosion and anti-corrosives, Sea-water corrosion, Offshore structures, Reinforced concrete--Deterioration
Format: Document (PDF)

Title: Effects of High Alkalinity Cements on the Control of Alkali-Silica Reaction for Reinforced Concrete.
Creator: Suarez, Jorge Alejandro, Hartt, William H., Florida Atlantic University, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: In previous research, cements with high alkali content (EqA 1.0-1.2 percent) extended the corrosion initiation time of reinforcing steel in concrete. During this study, laboratory tests were performed to determine the suitability of high alkalinity cements to improve concrete durability without modifying physical properties and to control the risk of alkali-aggregate reaction (AAR). A mix design for the FOOT-Class V concrete served as base material for this study. On a cubic meter basis the...
Show moreIn previous research, cements with high alkali content (EqA 1.0-1.2 percent) extended the corrosion initiation time of reinforcing steel in concrete. During this study, laboratory tests were performed to determine the suitability of high alkalinity cements to improve concrete durability without modifying physical properties and to control the risk of alkali-aggregate reaction (AAR). A mix design for the FOOT-Class V concrete served as base material for this study. On a cubic meter basis the cementitious material in this concrete included 363 kg of Type l/ll Portland cement and 83 kg of Class F fly ash. The water-to-cementitious material ratio of the concrete was 0.40. The fine aggregate used in the experimental concretes was quartz sand from a Florida source with no history of alkali-silica reactivity (ASR) susceptibility. A number of cement alkali contents were prepared by different additions of sodium hydroxide to the concrete mix (3.42 - 4.57 kglm\ in some cases, and by using different cements in others. Thus, effects on concrete susceptibility to ASR, electrical resistivity, and strength were studied. Pore water alkalinity was measured by ex-situ leaching and pore water extraction methods. It was concluded that leaching procedures were not appropriate to determine concrete pore water alkalinity in the presence of fly ash. Results suggested that it is feasible to use high alkali cement without the risk of ASR or the loss of strength for two of the seven coarse aggregates studied, given that supplementary cementitious materials and lithium nitrate admixtures are utilized. Criteria for qualification of a concrete as being ASR resistant was based on dimensional stability (less than 0.01% average specimen length change) and the absence of cracking over the one and two year exposure periods according to ASTM Cl293. Based on the fundamentals of the electric double layer theory, the incidence of bivalent cations adjacent to the surface of cement hydrates and reactive silica particles was proposed to provide an explanation for the effects of alkali addition on the electrical resistivity of concrete and the source of the expansive nature of the ASR gel.
Show less
Date Issued: 2006
PURL: http://purl.flvc.org/fau/fd/FA00012578
Subject Headings: Reinforced con crete construction, Concrete--Deterioration, Alkali-aggregate reactions, Silica
Format: Document (PDF)

Title: Hydrogen embrittlement of cathodically protected prestressing steel.
Creator: Kliszowski, Stanislas Henri., Florida Atlantic University, Hartt, William H., College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: Cathodic protection is currently recognized as the most practical mean for arresting corrosion of reinforcing steel tendons in existing concrete structures, however, its appropriateness in the case of prestressed concrete is questioned because prestressing steels are relatively susceptible to environmental cracking (hydrogen embrittlement). For the purpose of studying embrittlement tendencies a series of experiments using the slow strain rate technique were performed. The susceptibility to...
Show moreCathodic protection is currently recognized as the most practical mean for arresting corrosion of reinforcing steel tendons in existing concrete structures, however, its appropriateness in the case of prestressed concrete is questioned because prestressing steels are relatively susceptible to environmental cracking (hydrogen embrittlement). For the purpose of studying embrittlement tendencies a series of experiments using the slow strain rate technique were performed. The susceptibility to environmental cracking was compared for different steels corresponding to ASTM grades 270 and 250 polarized at $-$900 and $-1300$ mV (SCE) in deaerated saturated Ca(OH)$\sb2$ solutions. The influence of different notch and pit geometries was studied to simulate the behavior of corroded tendons and investigate the transition between smooth and severely notched specimen behavior. Also evaluated was the evolution of the mechanical properties of tendons after excessive polarization. The different cracking processes are discussed based on test data, fractography and exposures conditions associated with concrete structures.
Show less
Date Issued: 1994
PURL: http://purl.flvc.org/fcla/dt/14999
Subject Headings: Cathodic protection, Metals--Hydrogen embrittlement, Tendons (Prestressed concrete), Prestressed concrete--Deterioration, Prestressed steel construction
Format: Document (PDF)

Title: Corrosion Propagation of Rebar Embedded in High Performance Concrete.
Creator: Nazim, Manzurul, Presuel-Moreno, Francisco, Florida Atlantic University, College of Engineering and Computer Science, Department of Ocean and Mechanical Engineering
Abstract/Description: The FDOT has been using supplementary cementitious materials while constructing steel reinforced concrete marine bridge structures for over 3 decades. Previous findings indicated that such additions in concrete mix makes the concrete more durable. To better understand corrosion propagation of rebar in high performance concrete: mature concrete samples that were made (2008/2009) with Portland cement, a binary mix, a ternary mix and recently prepared (April 2016 with 50% OPC + 50% slag and 80%...
Show moreThe FDOT has been using supplementary cementitious materials while constructing steel reinforced concrete marine bridge structures for over 3 decades. Previous findings indicated that such additions in concrete mix makes the concrete more durable. To better understand corrosion propagation of rebar in high performance concrete: mature concrete samples that were made (2008/2009) with Portland cement, a binary mix, a ternary mix and recently prepared (April 2016 with 50% OPC + 50% slag and 80% OPC + 20% Fly ash) concrete samples were considered. None of these concretes had any admixed chloride to start with. An accelerated chloride transport process was used to drive chloride ions into the concrete so that chlorides reach and exceed thechloride threshold at the rebar surface and initiate corrosion. Electrochemical measurements were taken at regular intervals (during and after the electro-migration process) to observe the corrosion propagation in each sample.
Show less
Date Issued: 2017
PURL: http://purl.flvc.org/fau/fd/FA00004941, http://purl.flvc.org/fau/fd/FA00004941
Subject Headings: Reinforced concrete--Corrosion., Reinforced concrete--Chemical resistance., Reinforced concrete--Deterioration., Concrete--Corrosion., Concrete--Mechanical properties.
Format: Document (PDF)

Title: Correlation of Chloride Diffusivity and Electrical Resistance for Cracked Concrete.
Creator: Merantus, Stanley W., Reddy, Dronnadula V., Florida Atlantic University, College of Engineering and Computer Science, Department of Civil, Environmental and Geomatics Engineering
Abstract/Description: The durability of Reinforced Concrete (RC) structures in the Marine environment is causing serious concern in the structural infrastructure. Reinforced concrete structures, exposed to aggressive environments, are expected to last with little or no maintenance for long periods of time. However, one of the most serious environmental exposures that causes degradation is Chloride Diffusion, due to shrinkage, atmospheric corrosion, and tide-induced wet and dry conditions at the air-water...
Show moreThe durability of Reinforced Concrete (RC) structures in the Marine environment is causing serious concern in the structural infrastructure. Reinforced concrete structures, exposed to aggressive environments, are expected to last with little or no maintenance for long periods of time. However, one of the most serious environmental exposures that causes degradation is Chloride Diffusion, due to shrinkage, atmospheric corrosion, and tide-induced wet and dry conditions at the air-water interfaces of coastal structures. Therefore, chloride diffusivity, which correlates with the electrical resistivity, has a significant impact on the durability of concrete. Concrete chloride diffusivity has been experimented by multiple agencies and researchers on sound concrete, but there is a considerable need for investigation of the durability of cracked concrete in the marine environment. The two test methods carried out are presented: Standardized American Society for Testing and Materials (ASTM) C1202 for Rapid Chloride Permeability (RCP) and ASTM D257 for Surface Resistivity (SR), and Nordtest (NT) Build 492 for Rapid Chloride Migration (RCM) and Bulk Resistivity (BR) for both sound (uncracked) and cracked (micro and macro) concrete. The limitations of the ASTM method, due to measurements before the steady-state migration is reached, does not account for leakage in cracked concrete, and the heating of the specimen due to higher current that increase the conductivity are indicated. The Rapid Chloride Migration test provides for the non-steady state of diffusion. Again, Bulk Resistivity, in contradistinction to Surface Resistivity is more accurate for cracked concrete. The correlation betweeen RCM-BR are plotted. Chloride Permeability/Migration is an important parameter that governs the Durability of Concrete. The principal contribution is the highlighting of the inadequacy of the current widely used standard ASTM C1202 for diffusivity testing, and the need for revision with further investigation.
Show less
Date Issued: 2017
PURL: http://purl.flvc.org/fau/fd/FA00004942, http://purl.flvc.org/fau/fd/FA00004942
Subject Headings: Reinforced concrete--Construction--Corrosion., Reinforced concrete--Deterioration., Concrete--Corrosion., Concrete--Chemical resistance., Chlorides--Environmental aspects., Chlorides--Diffusion rate.
Format: Document (PDF)

Concrete--Deterioration (4)	+ -
Concrete -- Deterioration (3)	+ -
Cathodic protection (2)	+ -
Concrete--Corrosion. (2)	+ -
Corrosion and anti corrosives (2)	+ -

Reinforced concrete--Deterioration (2)	+ -
Reinforced concrete--Deterioration. (2)	+ -
Tubular steel structures -- Deterioration (2)	+ -
Air -- Pollution -- United States -- Measurement (1)	+ -
Air quality management (1)	+ -
Alkali-aggregate reactions (1)	+ -
Bulk solids flow (1)	+ -
Carbon steel (1)	+ -
Chlorides (1)	+ -
Chlorides--Diffusion rate. (1)	+ -
Chlorides--Environmental aspects. (1)	+ -
Concrete -- Corrosion (1)	+ -
Concrete construction (1)	+ -
Concrete, Effect of salt on (1)	+ -
Concrete--Chemical resistance. (1)	+ -
Concrete--Corrosion (1)	+ -
Concrete--Environmental testing (1)	+ -
Concrete--Mechanical properties. (1)	+ -
Corrosion (1)	+ -
Corrosion and anti-corrosives (1)	+ -
Diffusion (1)	+ -
Environmental health (1)	+ -
Fiber-reinforced concrete (1)	+ -
Florida (1)	+ -
High strength concrete (1)	+ -

Florida Atlantic University (13)	+ -
College of Engineering and Computer Science (12)	+ -
Department of Ocean and Mechanical Engineering (10)	+ -
Presuel-Moreno, Francisco (7)	+ -
Hartt, William H. (4)	+ -

Department of Civil, Environmental and Geomatics Engineering (2)	+ -
Arias, Wendy J. (1)	+ -
Chaix, Olivier. (1)	+ -
Cowan, David (1)	+ -
Kliszowski, Stanislas Henri. (1)	+ -
Le Floch, Anne. (1)	+ -
Meeroff, Daniel E. (1)	+ -
Merantus, Stanley W. (1)	+ -
Nazim, Manzurul (1)	+ -
Parkinson, Jacqueline Cecile (1)	+ -
Raof, Farhad Fakheri (1)	+ -
Reddy, Dronnadula V. (1)	+ -
Rosa-Pagan, Angel R. (1)	+ -
Seo, Bongjoon (1)	+ -
Suarez, Jorge Alejandro (1)	+ -
Weber, Brian W. (1)	+ -

Search In

Sort Results By:

Narrow results by:

Collection

Topical Subject

Genre

Type of Resource

Language

Creator

Format

Owner